1. Home
  2. Resources
  3. Process & materials
PROCESS × MATERIALS / Process & materials

Which materials run on which process

For selection and process handoff: the same process behaves differently on different materials. The table shows common combinations—● mature practice, ○ possible with review, — usually not this path. Matrix data matches the capabilities overview; no invented figures. How fine we can go is set after reviewing the drawing, material behavior, and volume.

Six processes Same workshop ● Mature practice ○ Possible—needs review — Usually not this path
00 / LEGEND

How to read this table

The matrix answers "do we often run this," not a drawing review. ○ is not a refusal—it means thickness, adhesive system, scrap path, and volume need a look first.

●

Mature practice

This material on this process is everyday shop practice with a clear path. Still send drawings to confirm contour, kiss-cut, and lead time—but you usually don't start from "can it be cut at all."

○

Possible—needs review

Possible, but more sensitive to thickness, hardness, debris, die-roll life, or volume thresholds. Quotes will flag risks; when volume is low or the structure is tricky, we may suggest another process.

—

Usually not this path

Not an absolute no—just an uncommon pairing for the line or the material (e.g. some materials aren't taped). Special needs? Describe conditions; we review case by case.

Full collaboration cadence (inquiry → sample → production) → How we work; process detail (kiss-cut, die rolls, peel, etc.) → the six process subpages below.

01 / MATRIX

Process × materials

Same table as overview "07 / Process & materials." On mobile, swipe sideways for all columns.

MaterialsFlatbed die cuttingRotary die cuttingPrecision slittingLaminatingAdhesive backingBlankingGasketSpoolingTaping
Double-sided tapeDOUBLE-COATED TAPE●●●●○○
FoamFOAM●○●●●○
Film / adhesive filmFILM●●●●○●
Rubber / SiliconeRUBBER · SILICONE●○○○●—
Metal foilALU / CU FOIL●○●○●—
Fabric / meshFABRIC · MESH●○●●○—
● Mature practice○ Possible—needs review— Usually not this path
02 / BY MATERIAL

Typical paths by material

Short notes on "how we usually pair processes"—cross-check the matrix. Detail and cases follow drawing review; grade TDS via quote or the upcoming datasheet channel.

Double-sided tape

DOUBLE-COATED TAPE

Flatbed / rotary die cutting, slitting, and laminating & backing are mature paths; blanked gaskets and spooling/taping are possible with review of adhesive system, thickness, and line form. Common outputs: sheets, nested parts, kiss-cut peel tabs, slit rolls. State bond substrate and temperature conditions with the selection.

Foam

FOAM

Flatbed die cutting, slitting, laminating & backing, and blanked gaskets are common; rotary and taping need review (thickness, compression, scrap). Thick stock with small holes stresses die life and scrap flow—sample first. Cushioning, sealing, and vibration parts often take this path.

Film / adhesive film

FILM

Most of the six processes are ●: die cutting, slitting, laminating, and taping are mature; blanked gaskets are ○ depending on thickness and contour. Good for thin insulating, masking, and labeling parts; kiss-cut and scrap method affect line placement—mark them clearly on the drawing.

Rubber / Silicone

RUBBER · SILICONE

Flatbed die cutting and blanked gaskets are mature; rotary, slitting, and laminating are mostly ○—review hardness and recovery. Spooling/taping usually isn't (—). For seals and gaskets, lock compression and groove fit first—don't copy the outline alone.

Metal foil

ALU / CU FOIL

Flatbed, slitting, and blanked gaskets are common; rotary and laminating need review (burrs, interlayer bond). Taping usually isn't. For conductive, shielding, and thermal parts, note allowed burr direction and whether an insulating laminate is required.

Fabric / mesh

FABRIC · MESH

Flatbed, slitting, and laminating & backing are mature; rotary and blanked gaskets need review (fiber fuzz, hole edges). Taping usually isn't. For mesh, reinforcement, and breathable structures, state warp/weft direction and whether fuzzy edges are allowed.

03 / SIX PROCESSES

Detail by process

The matrix only marks how common a pairing is; contours, kiss-cuts, die rolls, peel, and carrier orientation live on each subpage.

04 / NEXT

Next after the matrix

01

Check your material row

Read ● / ○ / —: mature paths can prep drawings from the process subpage; for ○, put thickness, adhesive system, and volume in the inquiry so we can review once.

02

Send drawings via the collaboration flow

CAD or sample + volume + lead time. We reply with a material plan, whether target tolerances are feasible, lead time, and price. See How we work。

03

Unsure? Sample first

Thick stock with small holes, kiss-cut depth, consignment debris/delamination—overview and process pages all stress: uncertain structures get sampled before volume.

Not sure about the pairing?
Send the material and drawing.

We'll recommend process and material from your conditions. Uncertain structures get sampled first.

→ Inquire now