Siminkey · Cellular silicone foam series · 6 grades

THERMOSIL PADS® SiliconeFoamCellular silicone foam · dense skin + honeycomb core

SurfaceSmooth dense non-porous surface with an internal open-cell honeycomb—one material for sealing, cushioning, damping, and thermal insulation. Continuous operating temperature -55°C ~ 200°C, flame rating UL94 V-0, thickness 0.8~30mm, 6 grades positioned by stress and structure—covering electronics, aerospace, automotive, and industrial scenes.

THERMOSIL PADS® is a registered trademark of Siminkey (Reg. No. 75957554). UL94 V-0 test reports available on request.

−55~200°C Wide temperature range Flame retardant UL94 V-0 Dense non-porous skin over open-cell honeycomb—composite structure Thickness 0.8~30mm

Roll widths 500 / 600 / 950mm · black / gray · cut, die-cut, blank, and adhesive-backable

THERMOSIL PADS® black cellular silicone foam sheet with dense skin, product shot on a dark background

THERMOSIL PADS® cellular silicone foam · black sheet

−55°C ~ 200°C
Continuous operating temperature
UL94 V-0
Flame rating · self-extinguishes after flame removal
0.8–13 mm
Thickness range
500 / 600 / 950 mm
Three roll widths
6 Major grades
Positioned by stress and structure
Low compression set
Low density · stable long-term sealing force

01 · Structure

One material,
two functional faces

THERMOSIL PADS® isn't homogeneous foam: the dense skin seals; the honeycomb core springs. Sealing and cushioning no longer trade off against each other.

Surface · dense silicone skin

Smooth, dense, non-porous. Strong surface sealing with dust and liquid resistance; a smooth mating face builds reliable seals at low pressure while protecting the foam core from wear and intrusion.

Core · open-cell honeycomb foam

3D open-cell honeycomb—low density, high recovery. Under load, cell walls buckle progressively to absorb energy, then rebound quickly when unloaded—the structural basis for low compression set and damping.

Result · sealing and cushioning together

The open-cell structure also lowers overall hardness and stress: in low-pressure scenes like battery cushioning and display sealing, it fills tolerance without jacking structural parts.

THERMOSIL PADS® cellular silicone foam close-up: dense skin and open-cell honeycomb core

Close-up: open-cell honeycomb foam under the dense skin

02 · Wide temperature range & flame rating

From −55°C to 200°C,
elastic across a wide range

From extreme cold outdoors to thermal cycling near engine bays, the silicone matrix stays flexible across a wide range—no embrittlement, no softening, no loss of spring. The full series passes UL94 V-0 vertical burn—suited to flame-rated electrical/electronic and transport equipment; test reports available on request.

UL94 V-0:In vertical burn testing, the specimen self-extinguishes within 10 seconds after flame removal, with no flaming drips that ignite cotton below—the baseline for flame-rated applications.

THERMOSIL PADS® silicone foam in a dark scene: sheets and sealing pads

Wide-range sealing and damping: one material across extreme temperature swings

THERMOSIL PADS® silicone foam sheets stacked to show 0.8~30mm thickness range

Full 0.8~30mm thickness series—select by tolerance and stress

03 · Performance properties

Low stress, long life,
four core properties

Material properties point to one outcome: after assembly, sealing and cushioning stay online for the long haul.

Low compression set

High recovery after long compression; sealing force decays slowly—suited to permanent assembly gaps and long-service seals.

Shock absorption

Open-cell structure absorbs impact and vibration energy—protects battery modules, displays, and precision structures, and improves system NVH.

Thermal insulation

Low-conductivity silicone matrix plus foam air cells form a light thermal barrier—a lightweight choice for thermal pads and insulation layers.

Aging & weather resistance

Resists UV, ozone, and damp-heat aging—stable outdoors and in cabin environments, cutting lifecycle maintenance replacements.

04 · Grade matrix

Six major grades—positioned by stress and structure

From ultra-low stress to high recovery; every grade shares −55~200°C operating temperature, UL94 V-0, and the 0.8~30mm thickness series—differences are stress level and structural orientation. Tap a card for the datasheet page.

#20Ultra-Soft

Ultra-soft

Ultra-low stress, soft conformability, low-pressure sealing and cushioning.

  • Stress levelUltra-low
  • Structural orientationSoft conformability · low-pressure sealing
  • Typical scenesBattery cushioning · display sealing
View specs
#21High-Performance

High-performance

Balanced overall performance—suited to display sealing and electronics cushioning.

  • Stress levelBalanced
  • Structural orientationBalanced overall performance
  • Typical scenesDisplay sealing · electronics cushioning
View specs
#23Low Stress Honeycomb

Low-stress honeycomb

Honeycomb structure—lightweight, low stress; large-panel cushioning.

  • Stress levelLow · lightweight
  • Structural orientationOpen-cell honeycomb structure
  • Typical scenesLarge panels · lightweight cushioning
View specs
#24Medium Stress

Medium stress

Medium stress—balanced support and cushioning.

  • Stress levelMedium
  • Structural orientationBalanced support and cushioning
  • Typical scenesStructural support · gap fill
View specs
#27High Performance

High-performance

High recovery—long-term stability in demanding environments.

  • Stress levelhigh
  • Structural orientationHigh recovery · long-term stability
  • Typical scenesEngine bay · outdoor equipment
View specs
#28High PerformanceHigh recovery

High-performance

Low density with high recovery, UL94 V-0—suited to demanding cushioning and sealing.

  • Stress levelhigh
  • Structural orientationLow density · high recovery
  • Typical scenesDemanding sealing & cushioning
View specs

Supports pointer drag with inertia · swipe can reverse anytime

05 · TechnicalParameters

Full technical specs

Series-level specs in one table; grade-level differences (stress, structure, density) are on each datasheet.

Materials
Cellular silicone (silicone foam), skin + core composite: smooth dense non-porous skin + open-cell honeycomb foam core
Operating temperature
−55°C ~ 200°C (continuous)
Flame rating
UL94 V-0
Thickness range
0.8~30mm
Roll width
500mm / 600mm / 950mm
Color
Black / gray (product shots on this page are black)
Series grades
#20 Ultra-Soft · #21 High-Performance · #23 Low Stress Honeycomb · #24 Medium Stress · #27 High Performance · #28 High Performance
Core properties
Low density · low compression set · aging & weather resistance · damping · thermal insulation
Typical applications
Sealing · cushioning · damping · thermal insulation (electronics / aerospace / automotive / industrial)

* Series-typical specs on this page; follow each grade datasheet. Custom cut, die-cut, blanking, and adhesive backing—confirm with an engineer.

06 · Applications

Four industries—one material logic

Wherever a tolerance needs filling, vibration needs absorbing, or heat needs blocking—that's where THERMOSIL PADS® belongs.

Electronics

  • Battery-module cushion pads and expansion absorption
  • Display and panel module sealing
  • Speaker dust and water sealing
  • PCB and precision-structure vibration support

Aerospace

  • Wide-temperature cabin and hatch sealing
  • Avionics vibration isolation mounts
  • Thermal insulation layers and thermal-management spacers
  • Large-panel and composite lightweight cushioning

Automotive

  • Interior cushioning and NVH treatment
  • Battery-pack sealing and thermal-management spacers
  • Harness and tubing hold cushions
  • Lamp and ECU sealing

Industrial

  • Equipment cabinet dust sealing
  • Tubing thermal insulation and cushioned hold-down
  • Precision-instrument shipping cushioning
  • Assembly gap fill and damping pads

07 · FAQ

FAQ about THERMOSIL PADS®

THERMOSIL PADS® cellular silicone foam has a continuous operating range of −55°C to 200°C. Across this wide range the material keeps elasticity and sealing performance—suited to extreme cold outdoors, cabin thermal cycling, and similar environments.

UL94 V-0 is a high flame rating in the UL94 vertical burn test: the specimen self-extinguishes within 10 seconds after flame removal, with no flaming drips that ignite cotton below. The THERMOSIL PADS® series meets UL94 V-0, matching typical flame requirements for electrical/electronic equipment and rail transit.

THERMOSIL PADS® uses a dense non-porous silicone skin over an open-cell honeycomb foam core. Versus open-surface foams, the dense skin seals, dust-proofs, and resists liquid better; versus EPDM/PU foam, the silicone matrix stays elastic from −55~200°C, with lower long-term compression set and stronger aging/weather resistance.

THERMOSIL PADS® standard roll widths are 500mm, 600mm, and 950mm, with thickness from 0.8~30mm. We can cut, die-cut, or blank to print, and support adhesive backing and other secondary converting. Confirm specs with a Siminkey engineer.

For battery-module cushioning and low-pressure sealing, prefer ultra-low-stress #20 Ultra-Soft; for large-panel cushioning and lightweight needs, prefer honeycomb #23 Low Stress Honeycomb; for balanced support choose #24 Medium Stress; #28 High Performance combines low density with high recovery for demanding cushioning and sealing.

Use Get a quote at the page bottom or in the nav to reach Siminkey. Share the target application, grade (or stress level), thickness, width, and volume—sample and production quotes usually within one business day.

08 · Selection & quote

For your application,
choose the right THERMOSIL PADS®

Share the target application, stress needs, thickness, and width—Siminkey engineers help select and ship samples quickly; production and custom converting (cut / die-cut / blank / adhesive backing) are all supported.

Usually replies within 1 business day · samples and production quotes welcome